8GB Kingston HyperX Fury Beast DDR3-1866 (1x8GB) RAM

8GB (1 x 8GB) | 1866Mhz | DDR3 | DIMM

Available: Out of Stock
$122.00

UNLEASH YOUR PERFORMANCE
8GB 1G x 64-Bit DDR3–1866 CL10 240-Pin Non ECC DIMM

Kingston FURY Beast DDR3 automatically overclocks to frequencies up to 1866MHz, dishing out an instant, hassle-free, reliable boost of power tuned for Intel’s 100 Series chipset. Beast’s asymmetric, edgy design stands out from the blocky, squared crowd and is crafted with quality aluminium. Rocking a black PCB, diamond-cut finish with coloured modules in blue, black and red makes the FURY Beast DDR3 amp up even the most audacious builds.

FURY KF318C10B/8 is a 1G x 64-bit (8GB) DDR3–1866 CL10 SDRAM (Synchronous DRAM) 2Rx8, memory module, based on sixteen 512M x 8-bit FBGA components per module. Each module has been tested to run at DDR3–1866 at a low latency timing of 10–11–10 at 1.5V. Additional timing parameters are shown in the Plug-N-Play (PnP) Timing Parameters section below. Each 240-pin DIMM uses gold contact fingers. The JEDEC standard electrical and mechanical specifications are as follows:

FACTORY TIMING PARAMETERS

  • Default (Plug N Play):
    • DDR3–1866 CL10–11–10–30 @ 1.5V
    • DDR3–1600 CL9–10–9 @ 1.5V
    • DDR3–1333 CL8–9–8 @ 1.5V
  • Note: The PnP feature offers a range of speed and timing options to support the widest variety of processors and chipsets. Your maximum speed will be determined by your BIOS.



FEATURES

  • JEDEC standard 1.5V Power Supply
  • VDDQ = 1.5V
  • 800MHz fCK for 1600Mb/sec/pin
  • 8 independent internal bank
  • Programmable CAS Latency: 11, 10, 9, 8, 7, 6
  • Programmable Additive Latency: 0, CL – 2, or CL – 1 clock
  • 8-bit pre-fetch
  • Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with tCCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS]
  • Bi-directional Differential Data Strobe
  • Internal(self) calibration: Internal self calibration through ZQ pin (RZQ : 240 ohm ± 1%)
  • On Die Termination using ODT pin
  • Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C
  • Asynchronous Reset
  • Height 1.338” (34mm) w/heatsink



SPECIFICATIONS

  • Memory Capacity: 8GB
  • Module Quantity: 1 Module
  • Speed: 1866MHz (PC3–14900)
  • Error Check: Non-ECC
  • Module Type: DIMM
  • CAS Latency: CL10
  • Form Factor: DDR3
  • Rank: 2R (Dual Rank)
  • Pins: 240 Pin
  • Memory Voltage: 1.5v
  • Memory Depth: 1G
  • Data Width: X64
  • Chip Organization: x8
  • Heat Spreader: Yes
  • CL(IDD): 10 cycles
  • Row Cycle Time (tRCmin): 48.125ns(min.)
  • Refresh to Active/Refresh Command Time (tRFCmin): 260ns(min.)
  • Row Active Time (tRASmin): 37.5ns(min.)
  • UL Rating: 94 V – 0
  • Operating Temperature: 0C to +85C
  • Storage Temperature: –55C to +100C

UNLEASH YOUR PERFORMANCE
8GB 1G x 64-Bit DDR3–1866 CL10 240-Pin Non ECC DIMM

Kingston FURY Beast DDR3 automatically overclocks to frequencies up to 1866MHz, dishing out an instant, hassle-free, reliable boost of power tuned for Intel’s 100 Series chipset. Beast’s asymmetric, edgy design stands out from the blocky, squared crowd and is crafted with quality aluminium. Rocking a black PCB, diamond-cut finish with coloured modules in blue, black and red makes the FURY Beast DDR3 amp up even the most audacious builds.

FURY KF318C10B/8 is a 1G x 64-bit (8GB) DDR3–1866 CL10 SDRAM (Synchronous DRAM) 2Rx8, memory module, based on sixteen 512M x 8-bit FBGA components per module. Each module has been tested to run at DDR3–1866 at a low latency timing of 10–11–10 at 1.5V. Additional timing parameters are shown in the Plug-N-Play (PnP) Timing Parameters section below. Each 240-pin DIMM uses gold contact fingers. The JEDEC standard electrical and mechanical specifications are as follows:

FACTORY TIMING PARAMETERS

  • Default (Plug N Play):
    • DDR3–1866 CL10–11–10–30 @ 1.5V
    • DDR3–1600 CL9–10–9 @ 1.5V
    • DDR3–1333 CL8–9–8 @ 1.5V
  • Note: The PnP feature offers a range of speed and timing options to support the widest variety of processors and chipsets. Your maximum speed will be determined by your BIOS.



FEATURES

  • JEDEC standard 1.5V Power Supply
  • VDDQ = 1.5V
  • 800MHz fCK for 1600Mb/sec/pin
  • 8 independent internal bank
  • Programmable CAS Latency: 11, 10, 9, 8, 7, 6
  • Programmable Additive Latency: 0, CL – 2, or CL – 1 clock
  • 8-bit pre-fetch
  • Burst Length: 8 (Interleave without any limit, sequential with starting address “000” only), 4 with tCCD = 4 which does not allow seamless read or write [either on the fly using A12 or MRS]
  • Bi-directional Differential Data Strobe
  • Internal(self) calibration: Internal self calibration through ZQ pin (RZQ : 240 ohm ± 1%)
  • On Die Termination using ODT pin
  • Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE < 95°C
  • Asynchronous Reset
  • Height 1.338” (34mm) w/heatsink



SPECIFICATIONS

  • Memory Capacity: 8GB
  • Module Quantity: 1 Module
  • Speed: 1866MHz (PC3–14900)
  • Error Check: Non-ECC
  • Module Type: DIMM
  • CAS Latency: CL10
  • Form Factor: DDR3
  • Rank: 2R (Dual Rank)
  • Pins: 240 Pin
  • Memory Voltage: 1.5v
  • Memory Depth: 1G
  • Data Width: X64
  • Chip Organization: x8
  • Heat Spreader: Yes
  • CL(IDD): 10 cycles
  • Row Cycle Time (tRCmin): 48.125ns(min.)
  • Refresh to Active/Refresh Command Time (tRFCmin): 260ns(min.)
  • Row Active Time (tRASmin): 37.5ns(min.)
  • UL Rating: 94 V – 0
  • Operating Temperature: 0C to +85C
  • Storage Temperature: –55C to +100C

Delivery Rates

Australia Delivery - We charge a flat rate of $5.90 AUD per shipment. Orders are shipped by air via Australia Post straight to your door! 

Delivery Times 

Orders ship from our fulfillment partner Mighty Ape. Their warehouse is based in New Zealand with daily flights across the Tasman with Australia Post.

As a result of courier delays in Australia due to Covid-19, the current standard delivery times for In Stock products using Australia Post are as follows:

  • QLD 3-5 business days
  • NSW 3-6 business days
  • ACT 4-6 business days
  • VIC 5-9 business days
  • SA 6-9 business days
  • TAS, WA 7-9 business days
  • NT 7-10 business days

      Customer Reviews

      No reviews yet
      0%
      (0)
      0%
      (0)
      0%
      (0)
      0%
      (0)
      0%
      (0)
      • Fast Shipping
        $5.90 Flat Rate
      • Customer Support
        AU/NZ Team
      • Easy Returns
        14 Day Returns
      • Secure Payment
        Transaction Protection
      • Largest Range
        Best Brands & Games

      Customer Reviews

      No reviews yet
      0%
      (0)
      0%
      (0)
      0%
      (0)
      0%
      (0)
      0%
      (0)